It is impossible to characterize the listening quality of even the simplest limiter or compressor based on specifications, because such specifications cannot adequately describe the crucial dynamic processes that occur under program conditions. Therefore, the only way to evaluate the sound of an audio processor meaningfully is by subjective listening tests. Certain specifications are presented here to assure the engineer that they are reasonable, to help plan the installation, and make certain comparisons with other processing equipment.
Except as noted, specifications apply for measurements from the analog left/right input to the analog #1 and analog #2 output.
Performance
Frequency Response (Bypass Mode):
±0.2 dB, 50 Hz–9.5 kHz, or as determined by user-settable high-pass and low-pass filters.
Noise:
Output noise floor will depend upon how much gain the processor is set for (Limit Drive, AGC Drive, Two-Band Drive, and/or Multiband Drive), gating level, equalization, noise reduction, etc. The dynamic range of the A/D Converter, which has a specified overload-to–noise ratio of 110 dB, primarily governs it. The dynamic range of the digital signal processing is 144 dB.
Total System Distortion (De-Emphasized, 100% Modulation):
<0.01% THD, 20 Hz–1 kHz, rising to <0.05% at 9.5 kHz. <0.02% SMPTE IM Distortion.
Polarity:
The processing employs phase rotation to maximize loudness. Therefore, the polarity is frequency-dependent.
Processing Sample Rate:
The 9300 is a “multirate” system, using internal rates from 32 kHz to 128 kHz as appropriate for the processing being performed. Audio clippers operate at 128 kHz.
Processing Resolution:
Internal processing has 24 bit (fixed point) or higher resolution; uses Motorola DSP56362 DSP chips.
Low-Pass Filter:
4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, or 9.5 (NRSC) kHz as set by user. Unit can be set up to comply easily with ITU-R and NRSC spectrum masks. Lowpass filter shape is parametric and can be set to be –0.1, –3, or –6 dB down at the cutoff frequency.
High-Pass Filter:
Constrained by user settable fifth-order “quasi-elliptical” highpass filter to 50, 60, 70, 80, 90, or 100 Hz. All filters have equal-ripple (Chebychev-like) passbands and a 25 Hz notch for transmitter protection.
Channel Configuration:
Processing is monophonic.
Installation
Analog Audio Input
Configuration:
Stereo (Configurable to drive the processing selection with mono from left, mono from right, or mono from sum).
Impedance:
10kΩ load impedance, electronically balanced. Through-hole pads are available on I/O module for user installed 600Ohm termination.
Nominal Input Level:
Software adjustable from -20.0 to +20.0 dBu (VU) / -13.0 to +27 dBu (PPM)
Maximum Input Level:
+27 dBu.
Connectors:
Two XLR-type, female, EMI-suppressed. Pin 1 chassis ground, Pins 2 (+) and 3 electronically balanced, floating and symmetrical.
A/D Conversion:
24 bit 128x oversampled delta sigma converter with linear-phase anti-aliasing filter. Converter outputs 64 kHz sample rate, which the 9300 then decimates to 32 kHz in DSP using an ultra-high-quality image-free synchronous sample rate converter.
Filtering:
RFI filtered, with high-pass filter at 0.15 Hz (-3 dB).
Analog Audio Output
Configuration:
Two monophonic outputs, capable to driving two transmitters. The two outputs have independent level controls.
Source Impedance:
351Ω (includes the third-order output EMI suppression network), electronically balanced and floating. The user can specify the output load in software to calibrate the output level accurately into a bridging or 600Ω load.
Load Impedance:
600Ω or greater, balanced or unbalanced. Termination not required or recommended.
Output Level (100% peak modulation):
Adjustable from -6 dBu to +20 dBu peak, into 600Ω or greater load, software-adjustable.
Signal-to-Noise:
≥ 90 dB unweighted (Bypass mode, de-emphasized, 20 Hz - 9.5 kHz bandwidth, referenced to 100% modulation).
Distortion:
≤ 0.01% THD (Bypass mode, de-emphasized) 20 Hz - 9.5 kHz bandwidth.
Connectors:
Two XLR-type, male, EMI-suppressed. Pin 1 chassis ground, Pins 2 (+) and 3 electronically balanced, floating and symmetrical.
D/A Conversion:
24 bit 128x oversampled.
Filtering:
RFI filtered.
Digital Audio Input
Input Reference Level:
Software adjustable from -30.0 dBFS to -10 dBFS (VU) / -23.0 dBFS to -3.0 dBFS (PPM)
Configuration:
Stereo per AES3 standard, 24 bit resolution, software processing selection of mono from left, mono from mono from sum.
Sampling Rate:
32, 44.1, 48, 88.2 or 96 kHz, automatically selected.
Connector:
XLR-type, female, EMI-suppressed. Pin 1 chassis ground, pins 2 and 3 transformer balanced and floating, 110Ω impedance.
Input Reference Level:
Variable within the range of -30 dBFS to -10 dBFS.
J.17 De-emphasis:
Software-selectable.
Filtering:
RFI filtered.
Digital Audio Output
Configuration:
Dual-channel per AES3 standard. Each channel carries an identical monophonic signal.
Sample Rate:
Internal free running at 32, 44.1, 48, 88.2 or 96 kHz, selected in software. Can also be synced to the AES3 input at 32, 44.1, 48, 88.2 or 96 kHz, as configured in software.
Word Length:
Software selected for 24, 20, 18, 16 or 14-bit resolution. First-order highpass noise-shaped dither can be added. Dither level automatically adjusted appropriately for the word length.
Connector:
XLR-type, male, EMI-suppressed. Pin 1 chassis ground, pins 2 and 3 transformer balanced and floating, 110 Ω impedance.
Output Level (100% peak modulation):
-20.0 to 0.0 dBFS software controlled.
Filtering:
RFI filtered.
Remote Computer Interface
Supported Computer and Operating System:
IBM-compatible PC running Microsoft Windows® 2000 (SP3 or higher) or XP, ME vista 7, and 8, 8.1 and 10
Configuration:
TCP/IP protocol via direct cable connect, modem, or Ethernet interface. Suitable null modem cable for direct connect is supplied. Modem and other external equipment is not supplied.
Serial Connector:
RS–232 on DB–9 male connector, EMI-suppressed. Uses PPP to provide for direct or modem connection to the 5500i PC Remote application.
Ethernet Connector:
Female RJ45 connector for 10-1000 Mbps networks using CAT5 cabling. Native rate is 100 Mbps. Provides for connection to the 9300 PC Remote application through either a network, or, using a crossover Ethernet cable, directly to a computer.
Ethernet Networking Standard: TCP/IP.
SNMP: User configurable OPTIMOD SNMP Agent to monitor the Optimod’s status and to send Alarm notifications via the Optimod Ethernet connector to the network.
SNMP Version: SNMPv2 with Read-write (RW) access to a couple of MIB objects.
SNMP Features: 31 object types for System Configuration, I/O, Modulation Levels and Traps like Get/Query - Set/Control - Traps/Alert
SNMP Mib file: Delivered with Remote Control Application Software.
Remote Control (GPI) Interface
Configuration:
Eight (8) inputs, opto-isolated and floating.
Voltage:
6 - 15 V AC or DC, momentary or continuous. 12 VDC provided to facilitate use with contact closure.
Connector:
DB-25 male, EMI-suppressed.
Control:
User-programmable for any four of user presets, factory presets, bypass, test tone, mono L mode, mono R mode, mono sum mode, analog input, digital input, clock reset, status bit pass/block, and Transmission presets.
Filtering:
RFI filtered.
Tally Outputs
Circuit Configuration: Two NPN open-collector outputs.
Voltage: +15 volts maximum. Do not apply negative voltage. When driving a relay or other inductive load, connect a diode in reverse polarity across the relay coil to protect the driver transistors from reverse voltage caused by inductive kickback.
Current: 30 mA maximum
Indications: Tally outputs can be programmed to indicate a number of different operational and fault conditions, including Input: Analog, Input: Digital, Analog Input Silent, AES Input Silent, and AES Input Error.
Filtering: RFI filtered.
Power
Voltage:
Universal switching power supply, 85 - 264 VAC, 50 - 60 Hz, 15 VA.
Connector:
IEC, EMI-suppressed. Detachable 3-wire power cord supplied.
Grounding:
Circuit ground is hard-wired to chassis ground.
Safety Standards:
ETL listed to UL standards, CE marked.
Environmental
Operating Temperature:
32 ° to 122 °F / 0 ° to 50 °C for all operating voltage ranges.
Humidity:
0 - 95% RH, non-condensing.
Dimensions (W x H x D):
19" x 1.75" x 14.25" / 48.3 cm x 4.5 cm x 36.2 cm. One rack unit high. RFI / EMI Tested according to Cenelec procedures. FCC Part 15 Class A device.
Shipping Weight & Dimensions:
18 lbs / 8.2 kg - 23" x 23" x 6"
Warranty
Five Years, Parts and Service Subject to the limitations set forth in Orban's Standard Warranty Agreement.